When designing electronic enclosures, industrial equipment, and systems operating in demanding environments, engineers invest considerable effort in sealing covers, connectors, cables, and mechanical interfaces.
However, one small and seemingly simple component – the mounting screw – can become a potential weak point in the enclosure’s sealing system.
Even when an enclosure uses a high-quality perimeter gasket, liquids may find a path through mounting holes, gaps between screw heads and mounting surfaces, or along threaded connections.
The SFR6-32X3/8-2615 sealing screw by APM Hexseal belongs to the SEELSKREW family and combines a flat countersunk screw with an integrated elastomeric O-ring positioned beneath the screw head.
This design combines mechanical fastening with localized sealing around the screw interface, potentially eliminating the need for a separate sealing washer beneath each screw head.
The SFR6-32X3/8-2615 features a 6-32 UNC thread, a nominal length of 3/8 inch, and a Fluorosilicone sealing element.
It is particularly relevant to applications requiring reliable mechanical fastening and localized protection against liquid ingress.
Why Can Conventional Screws Compromise Enclosure Sealing?
In sealed electronic systems, attention is usually focused on major sealing interfaces, including enclosure gaskets, electrical connectors, and cable entries.
However, every mounting hole represents another potential leakage path.
When a conventional screw is installed, the contact between its head and the mounting surface does not necessarily create a liquid-tight seal.
Even when the screw is properly tightened, surface roughness, manufacturing tolerances, local irregularities, and mechanical movement may allow liquids to pass through the fastening interface.
In certain configurations, liquids can also travel along the screw threads and reach the interior of the enclosure.
This concern becomes particularly important in equipment exposed to water spray, cleaning operations, moisture, or industrial fluids.
Why Not Simply Use a Sealing Washer?
A separate sealing washer can provide an effective solution in suitable applications, but it introduces an additional component into the assembly process.
The washer must be correctly positioned, compatible with the joint geometry, and compressed appropriately.
In assemblies containing numerous screws, additional components can increase assembly complexity and the possibility of installation errors.
A sealing screw with an integrated O-ring combines the fastening element and the sealing component into a single supplied assembly.
SFR6-32X3/8-2615 – Screw Design and Sealing Principle
The APM Hexseal SEELSKREW family combines a metallic fastening element with an elastomeric sealing ring.
The SFR6-32X3/8-2615 uses a flat countersunk head with an 82-degree angle and a cross-recess drive.
The O-ring is positioned beneath the screw head, according to the manufacturer’s design.
When installed in a properly designed countersunk mounting hole and tightened appropriately, the O-ring is compressed between the screw head and the mounting surface.
This compression is intended to create a localized barrier against liquid ingress through the screw interface.
The effectiveness of the seal depends not only on the screw itself but also on mounting-hole geometry, surface condition, O-ring compression, and operating conditions.
Understanding the SFR6-32X3/8-2615 Part Number
One advantage of the SEELSKREW product family is its structured part-number system, which identifies the mechanical configuration and sealing material.
| Part number element | Description |
|---|---|
| SFR | SEELSKREW flat countersunk head, cross-recess drive |
| 6-32 | 6-32 UNC inch thread |
| X | Separator between thread size and screw length |
| 3/8 | Nominal screw length of 3/8 inch |
| 2615 | Fluorosilicone rubber O-ring |
The 2615 suffix is particularly important because it identifies the sealing material.
Other O-ring materials are available within the SEELSKREW product family, allowing engineers to select an appropriate material for different operating environments.
Technical Specifications – SFR6-32X3/8-2615
| Parameter | Specification |
|---|---|
| Manufacturer | APM Hexseal |
| Product family | SEELSKREW |
| Part number | SFR6-32X3/8-2615 |
| Screw type | Flat Head, Cross Recess |
| Countersunk head angle | 82° |
| Thread | 6-32 UNC |
| Nominal screw length | 3/8 inch (9.525 mm) |
| Standard screw material in the series | 18/8 stainless steel |
| Standard finish | Passivated, according to AMS2700 |
| O-ring material | Fluorosilicone Rubber |
| O-ring material service temperature | -61°C to +232°C |
| Sealing arrangement | Integrated O-ring beneath the screw head |
| Installation | Suitable countersunk mounting hole |
The specifications describe the product configuration and standard characteristics of the SEELSKREW family. Exact dimensions, material configuration, and installation requirements should be confirmed against the applicable manufacturer drawing before production.
The specified temperature range refers to the Fluorosilicone sealing material and does not independently establish the operating temperature limits of the complete screw assembly.
Fluorosilicone – Why Does the Sealing Material Matter?
The 2615 suffix identifies an O-ring manufactured from Fluorosilicone Rubber.
Fluorosilicone is an elastomer that combines characteristics of silicone rubber with improved resistance to certain fuels, oils, and other fluids compared with conventional silicone.
According to the APM Hexseal material table, the specified service temperature range for Fluorosilicone is:
-61°C to +232°C
This wide temperature range makes the material relevant for evaluation in equipment exposed to low or elevated temperatures.
However, chemical compatibility must always be evaluated against the specific fluid, concentration, temperature, and duration of exposure.
A wide service temperature range does not automatically mean that the material is suitable for every chemical environment or sealing application.
Alternative O-Ring Materials
APM Hexseal offers several sealing materials within the SEELSKREW product family.
| Material suffix | O-ring material | Manufacturer’s material service temperature |
|---|---|---|
| 2701 | Silicone Rubber | -101°C to +260°C |
| 2615 | Fluorosilicone Rubber | -61°C to +232°C |
| 5701 | Viton A | -29°C to +204°C |
| 4601 | Buna-N / NBR | -54°C to +121°C |
| 3701 | Neoprene | -54°C to +149°C |
| 7601 | EPDM | -54°C to +149°C |
These temperature ranges refer to the sealing materials listed in the manufacturer’s documentation.
Actual suitability depends on the complete application, including chemical exposure, mechanical compression, pressure, and operating conditions.
CASE STUDY: Improving Sealing Around Mounting Screws in an Industrial Control Enclosure
The following case study illustrates a potential engineering application of the SFR6-32X3/8-2615. It is an illustrative design scenario, not a documented customer installation or a verified test result.
The Challenge: A Sealed Enclosure with Potential Leakage Paths
Consider an electronic control system installed near industrial machinery.
The enclosure contains an electronic circuit board, electrical connectors, and a perimeter gasket between the cover and the enclosure body.
The equipment is exposed to occasional water spray and periodic cleaning procedures.
During the initial design, conventional countersunk screws are selected to secure the enclosure cover.
Although the perimeter gasket provides sealing between the cover and the enclosure body, the engineering team identifies a potential leakage path through the mounting holes, particularly where the holes communicate with the enclosure interior.
Applying liquid sealant around every screw is undesirable because it may complicate cover removal during maintenance.
Using separate sealing washers is another possible solution, but it introduces additional components and assembly operations.
The Solution: Integrating SFR6-32X3/8-2615 SEELSKREW Fasteners
The proposed solution uses APM Hexseal SFR6-32X3/8-2615 sealing screws.
Each screw incorporates a Fluorosilicone O-ring beneath its countersunk head.
During the mechanical design stage, the mounting-hole geometry is checked against the manufacturer’s requirements, including clearance-hole diameter, countersink angle, and countersink depth.
When the screw is tightened, the integrated O-ring is compressed against the mounting surface.
The objective is to restrict liquid ingress through the fastening interface.
Instead of installing a separate sealing washer at each mounting point, the fastening and sealing elements are supplied together as one assembly.
Numerical Example: An Enclosure with 12 Mounting Screws
Consider an industrial enclosure requiring 12 mounting screws.
| Parameter | Conventional screws with separate sealing washers | SEELSKREW |
|---|---|---|
| Number of screws | 12 | 12 |
| Separate sealing washers | 12 | 0 |
| Total supplied fastening and sealing assemblies/components | 24 | 12 |
| Integrated sealing element | No | Yes |
In this example, replacing conventional screws and separate sealing washers with SEELSKREW assemblies reduces the number of separately handled fastening and sealing components from 24 to 12.
This represents a 50% reduction in the number of separately handled components for these fastening points.
The calculation relates only to component count. It does not represent a measured reduction in assembly time, manufacturing cost, or installation errors.
Why Select SFR6-32X3/8-2615?
1. Integrated sealing element
The O-ring is supplied as part of the screw assembly, eliminating the need for a separate sealing washer in suitable applications.
2. Standard 6-32 UNC thread
The screw can be evaluated for equipment using 6-32 UNC threaded connections, subject to mechanical compatibility and required thread engagement.
3. Countersunk head configuration
The flat-head geometry supports installation in an appropriately designed countersunk mounting hole.
4. Fluorosilicone sealing material
The material offers a wide specified service temperature range and potential compatibility with selected industrial fluids, subject to verification.
5. Stainless steel construction
The standard 18/8 stainless steel material used in the series provides corrosion resistance in many environments, depending on exposure conditions.
Engineering Outcome
Using SEELSKREW fasteners can simplify assembly and provide a localized sealing solution around mounting holes.
The approach reduces the need to handle separate sealing washers and allows mechanical fastening and sealing to be considered as one integrated interface.
However, the final enclosure must be tested under the expected operating conditions to verify sealing performance.
A sealing screw alone does not establish an IP rating for the complete enclosure.
Why Is Mounting-Hole Geometry Just as Important as the Screw?
A common design mistake is assuming that a conventional screw can be replaced with a sealing screw without reviewing the mounting-hole geometry.
In practice, sealing performance depends on the complete mechanical interface.
The SFR6-32X3/8-2615 uses an 82-degree countersunk head.
The clearance hole, countersink, and surrounding mounting surface must be compatible with the manufacturer’s design.
Important engineering considerations include:
- Correct clearance-hole diameter.
- Appropriate countersink angle and depth.
- Suitable surface finish around the sealing interface.
- Adequate O-ring compression.
- Proper thread engagement.
- Suitable tightening torque.
Excessive tightening may damage the sealing element or mounting surface, while insufficient tightening may prevent the O-ring from achieving the required compression.
The appropriate tightening torque must be determined according to the joint design, screw material, enclosure material, and manufacturer’s recommendations.
Generic torque values should not be applied without engineering verification.
Inch vs. Metric Sealing Screws – SFR and SFRM
APM Hexseal offers SEELSKREW solutions for both inch and metric fastening systems.
The inch-thread SFR family includes configurations with 82-degree countersunk heads.
The metric SFRM family described in the manufacturer’s drawing uses a 100-degree countersunk head.
This distinction is important because replacing one countersunk-head geometry with another can affect mechanical contact and sealing compression.
| Parameter | SFR inch series | SFRM metric series |
|---|---|---|
| Thread system | Inch | Metric |
| Countersunk head angle | 82° | 100° |
| Example part number | SFR6-32X3/8-2615 | SFRM3X6MM-2701 |
| O-ring material options | Multiple options | Multiple options |
| Typical application | Inch-thread assemblies | Metric-thread assemblies |
Selecting the correct sealing screw requires compatibility with the thread, countersunk geometry, sealing material, and intended operating environment.
Engineering Considerations When Selecting a Sealing Screw
Before choosing a sealing screw for an electronic enclosure or industrial assembly, several parameters should be evaluated.
Thread Size and Screw Length
The screw must match the threaded connection, component thickness, and required thread engagement.
Head Geometry
Countersink angle, clearance-hole diameter, and mounting depth must be compatible with the selected screw.
Sealing Material
The elastomer should be selected according to the expected fluids, temperatures, pressure conditions, and environmental exposure.
Screw Material
Material selection should consider mechanical strength, corrosion resistance, and compatibility with the enclosure materials.
Tightening Torque
The joint must provide sufficient mechanical fastening and appropriate O-ring compression without damaging the components.
Environmental and Ingress Protection Testing
The completed assembly should be evaluated under its intended operating conditions, particularly when IP ratings or demanding environmental requirements apply.
Frequently Asked Questions (FAQ)
What is the SFR6-32X3/8-2615?
The SFR6-32X3/8-2615 is an APM Hexseal SEELSKREW sealing screw featuring a 6-32 UNC thread, a nominal length of 3/8 inch, an 82-degree countersunk head, and an integrated Fluorosilicone O-ring.
What is the difference between a SEELSKREW and a conventional screw?
A SEELSKREW includes an integrated sealing element designed to create a barrier against liquid ingress through the screw interface when installed under suitable conditions.
Can a SEELSKREW replace a conventional screw and sealing washer?
In suitable applications, the integrated O-ring can eliminate the need for a separate sealing washer beneath the screw head.
Mechanical and sealing compatibility must be verified.
Is the SFR6-32X3/8-2615 suitable for high temperatures?
The Fluorosilicone sealing material is listed with a service temperature range of -61°C to +232°C.
Suitability of the complete screw assembly depends on the operating environment and the specifications of all relevant components.
Is Fluorosilicone suitable for exposure to oils and fuels?
Fluorosilicone may provide resistance to certain oils and fuels, but chemical compatibility must be verified for the specific fluid and exposure conditions.
Does the SFR6-32X3/8-2615 guarantee IP67 or IP68 protection?
No. An enclosure’s IP rating cannot be determined from the screw specifications alone.
Achieving a specific IP rating requires appropriate enclosure design and testing of the complete assembly.
Are metric versions available?
Yes. APM Hexseal offers the SFRM metric sealing screw family with metric threads and corresponding countersunk-head geometry.
Can other O-ring materials be specified?
Yes. The manufacturer’s documentation lists several options, including Silicone, Fluorosilicone, Viton A, Buna-N, Neoprene, and EPDM, subject to the availability of the required configuration.
Can the screw be removed and reinstalled?
The screw can be mechanically removed, but reuse of the sealing element should not be assumed without inspection and verification.
O-ring condition, compression history, and the manufacturer’s recommendations should be considered before reassembly.
Technical Glossary
Sealing Screw: A fastening element incorporating a sealing component intended to restrict fluid ingress through the fastening interface.
O-Ring: An elastomeric ring with a circular cross-section that creates a seal through controlled compression.
Fluorosilicone: An elastomer combining characteristics of silicone rubber with improved resistance to certain oils, fuels, and other fluids.
Countersunk Head: A conical screw-head geometry designed for installation in a matching countersunk hole.
UNC (Unified National Coarse): An inch-based screw-thread series with coarse thread pitch.
Passivation: A chemical surface treatment used to improve the corrosion resistance of stainless steel.
IP Rating (Ingress Protection): A classification describing the protection provided by an enclosure against the ingress of solid objects and water, according to the applicable standard.
Thread Engagement: The length or extent of contact between mating internal and external screw threads.
Compression Set: The permanent deformation that may remain in an elastomer after prolonged compression.
Conclusion: SFR6-32X3/8-2615 as an Integrated Fastening and Sealing Solution
The SFR6-32X3/8-2615 sealing screw by APM Hexseal provides an engineering solution for a fastening interface that is sometimes overlooked during enclosure design.
By combining a stainless steel countersunk screw with an integrated Fluorosilicone O-ring, the product allows engineers to address mechanical fastening and localized sealing within a single assembly.
This approach can reduce the number of separately handled components, simplify installation, and help restrict liquid ingress through mounting holes.
Successful sealing, however, depends on proper mounting-hole geometry, suitable material selection, controlled tightening, and validation of the complete assembly.
Amironic Ltd., the Israeli representative of APM Hexseal, provides technical and commercial support for selecting SEELSKREW sealing screws and other sealing solutions according to the mechanical, environmental, and operational requirements of each application.
For technical assistance, product selection, or a quotation for the SFR6-32X3/8-2615 and other APM Hexseal sealing products, contact Amironic.


